Jonsered GR 2126D Betreibershandbuch

Operator´s manual (EPA)Please read these instructions carefullyand make sure you understand thembefore using the machine.

10 – EnglishSAFETY INSTRUCTIONSCutting equipmentSharpening thegrass blade• See the cuttingequipment’s packaging forcorrect filing instructions.• The b

English – 11SAFETY INSTRUCTIONSGeneral safety instructionsIMPORTANT INFORMATION• This machine is intended solely for trimming andclearing grass and fo

12 – EnglishGeneral working instructionsSAFETY INSTRUCTIONSBasic safety precautions1.Observe your surroundings:• To ensure that people, animals or oth

English – 13SAFETY INSTRUCTIONSAdjusting the harness and clearing sawDesignations• Use a saw blade forcutting woody growthwith thin stems.• Use a gras

14 – EnglishSAFETY INSTRUCTIONSClearing‘s ABCA. Always use the correct equipment.B. Always have well adjusted equipment.C. Follow the safety instructi

English – 15SAFETY INSTRUCTIONSGrass clearingusing the trimmerhead and plasticblades.• Hold the trimmer headjust above the ground atan angle. It is th

16 – EnglishWHAT IS WHAT?What is what on the brushcutter?1. Blade2. Grease filler cap3. Angle gear4. Combination guard5. Shaft6. Handlebars7. Throttle

English – 17Assembling the handlebarsASSEMBLY• Remove the screw at therear of the throttlehandle.• Slide on the throttlehandle on the right-handside o

18 – EnglishASSEMBLYAssembling the blade guard andclearing blade• Remove the mountingplate (H). Fit the adapter(I) and bracket (J) withthe two screws

English – 19ASSEMBLY• Fit the appropriateguard (A) for use withthe trimmer head. Hookthe guard onto the shaftfitting and secure it withthe bolt (L).•

2 – EnglishSymbolsSYMBOL EXPLANATIONWARNING! Clearing saws,brushcutters and trimmers can bedangerous!Careless or incorrect use can result inserious or

20 – EnglishFUEL HANDLINGFuel mixtureNOTE!The machine is fitted with a two-stroke engine and mustalways be run on a mixture of petrol and two-stroke o

English – 21START AND STOPControl before startingFor reasons of safety followthese recommendations!• Check the blade to ensurethat no cracks have form

22 – EnglishMAINTENANCECarburettorYour JONSERED product has been designed andmanufactured to specifications that reduce harmfulemissions. After your u

English – 23Correctly adjusted carburettorA correctly adjusted carburettor means that the machineaccelerates without hesitation and the machine 4-cycl

24 – EnglishMAINTENANCECooling systemTo maintain as low opera-ting temperature as possiblethe engine is equipped witha cooling system.The cooling syst

English – 25MAINTENANCESpark plugThe condition of the sparkplug is affected by:• An incorrect carburettorsetting.• An incorrect fuel mixture(too much

26 – EnglishMAINTENANCESharpening the clearing blade!WARNING!Incorrect cutting equipment or anincorrectly sharpened blade increasesthe risk of kickbac

English – 27TECHNICAL DATATechnical dataEngineDisplacement, cu. in/cm3Cylinder bore, inch/mmStroke length, inch/mmRecommended max. speed, rpmIdling sp

28 – EnglishEMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS ANDOBLIGATIONSThe EPA (U.S. Environmental Protection Agency),Environment Canada an

English – 291Poly Trim2345678>20mm>20mm!BA6 NmX 10

English – 3CONTENTSList of contentsSYMBOL EXPLANATIONSymbols ... 2CONTENTS

30 – English1Trimmy H II234567897,5 m 25'2,0-2,4 mm.080-.095"12 15 cm 6"~ 3,7 m 12' 15 cm 6"´*xre¶5¶¨

English – 311Tap-N-Go Pro2567891012“Click”347,5 m 25'2,0-2,4 mm.080-.095"15 cm 6"~ 3,7 m 12'1.)2.)1115 cm 6"15 c

2002W11´*xre¶5¶¨108 88 26-95

4 – EnglishThe machine‘s safety equipmentThis section describes the machine‘s safety equipment, itsfunction and how checks and maintenance are carried

English – 52. Stop switchThe stop switch should beused to stop the engine.3. Cuttingattachment guardThis guard is intended toprevent objects from bein

6 – EnglishSAFETY INSTRUCTIONS6. MufflerThe muffler is designed togive the lowest possible noiselevel and to direct theengine‘s exhaust fumes awayfrom

English – 7SAFETY INSTRUCTIONS1. Throttle triggerlock• Check that the throttle islocked in the “idlingposition“ when thethrottle trigger lock is inits

8 – EnglishSAFETY INSTRUCTIONS3. Cuttingattachment guard• Check that the guard isundamaged and notcracked.• Replace the guard if it hasbeen exposed to

English – 97. Quick-release• Check that the harnessstraps are correctlypositioned. When theharness and machine areadjusted, check the harness‘safety r