Jonsered GC 2125C Bedienungsanleitung

GT 2125 GC 2125 GC 2125C Oper ator’s manual (EPA) Please read the oper ator’s manual carefully and make sure you understand the instructions before

10 – EnglishGENERAL SAFETY PRECAUTIONSGeneral rulesOnly use cutting attachments with the guards we recommend! See the chapter on Technical data.Keep t

English – 11ASSEMBLYFitting the loop handle(GT 2125)• Position the handle on the shaft. Note that the handle must be mounted below the arrow on the sh

12 – EnglishASSEMBLYAssembling and dismantling the two-piece shaft(GC 2125C)Assembly:• Loosen the coupling by turning the knob.• Align the tab of the

English – 13ASSEMBLY• Insert a finger into the centre hole of the cover (I) while grasping the cover with your other fingers. Using the index finger and

14 – EnglishASSEMBLYFitting the trimmer guard and trimmer head(GT 2125)Guard• Fit the guard as shown in the diagram. Tighten securely.Trimmer head• Fi

English – 15FUEL HANDLINGFuel safetyNever start the machine:1 If you have spilled fuel on it. Wipe off the spillage and allow remaining fuel to evapor

16 – EnglishFUEL HANDLINGMixing• Always mix the gasoline and oil in a clean container intended for fuel.• Always start by filling half the amount of th

English – 17STARTING AND STOPPINGCheck before starting• Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the cent

18 – EnglishSTARTING AND STOPPINGCAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully

English – 19WORKING TECHNIQUESGeneral working instructionsBasic safety rules1 Look around you:• To ensure that people, animals or other things cannot

2 – English KEY T O SYMBOLS Symbols W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in s

20 – EnglishWORKING TECHNIQUESGrass clearing using a grass blade• Grass blades and grass cutters must not be used on woody stems.• A grass blade is us

English – 21WORKING TECHNIQUESSweeping• The fan effect of the rotating cord can be used for quick and easy clearing up. Hold the cord parallel to and

22 – EnglishMAINTENANCECarburetorYour Jonsered product has been designed and manufactured to specifications that reduce harmful exhaust fumes. The engi

English – 23MAINTENANCEFine adjustment of the idle speed TAdjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. Fir

24 – EnglishMAINTENANCECooling systemTo keep the working temperature as low as possible the machine is equipped with a cooling system.The cooling syst

English – 25MAINTENANCETwo-piece shaft (GC 2125C)The drive shaft end in the lower shaft should be lubricated with grease every 30 hours. There is a ri

26 – EnglishMAINTENANCEMaintenance scheduleThe following is a list of the maintenance that must be performed on the machine. Most of the items are des

English – 27TECHNICAL DATATechnical dataNote 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure lev

28 – EnglishTECHNICAL DATAThe accessories are recommended for use in combination with the specified power heads and have been evaluated to applicable I

English – 29FEDERAL EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONSThe EPA (The US Environmental Protection Agency), Environme

English – 3 CONTENTS Contents Note the f ollowing before starting: Please read the oper ator’s manual carefully.Maintenance, replacement, or repair

"Clic"12356796,0 m18'483,05 m9'2,0-2,4 mm.079-.095"10 cm 4"6"15 cmTap-N-Go 25

1Trimmy H II234567897,5 m 25'2,0-2,4 mm.080-.095"12 15 cm 6"~ 3,7 m 12' 15 cm 6"

"Clic"12356710118,5 m28'484,2 m14'2,4-2,7 mm.095-.106"10 cm 4"6"15 cmS35

12432,4-2,7 mm.095-.106"4,25 m14'4,25 m14'B6"15 cmA6"15 cmS355

´®z+R;3¶5y¨´®z+R;3¶5y¨Tap-N-Go 35"Clic"12356798,5 m28'484,3 m14'2,4-2,7 mm.095-.106"10 cm 4"6"15 cm

1Auto 3223456789104,0 m 13'2,4 mm.095"~2,0 m6,5'6"6"15 cm15 cm

´®z+R;3¶5y¨2007-01-25´®z+R;3¶5y¨1150271-95

4 – English INTR ODUCTION Dear customer! Cong ratulations on your choice to buy a Jonsered product!Your purchase gives you access to professional h

English – 5 WHA T IS WHA T? What is what?3130GC2125C 1 Trimmer head2 Grease filler cap, bevel gear3 Bevel gear4 Cutting attachment guard5 Shaft6 Lo

6 – English GENERAL SAFETY PRECA UTIONS Impor tant Personal protective equipment HELMET A protectiv e helmet where there is a risk of falling objec

English – 7 GENERAL SAFETY PRECA UTIONS CLO THINGWear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches

8 – English GENERAL SAFETY PRECA UTIONS Cutting attac hment guard This guard is intended to pre vent loose objects from being thrown towards the op

English – 9GENERAL SAFETY PRECAUTIONSIf the muffler on your machine is fitted with a spark arrestor screen this must be cleaned regularly. A blocked scr