Jonsered GC 2125 Bedienungsanleitung

GT 2125 GC 2125 GC 2125C Oper ator’s manual Please read the oper ator’s manual carefully and make sure you understand the instructions before using

10 – EnglishGENERAL SAFETY PRECAUTIONSSharpening grass cutters and grass blades• See the cutting attachment packaging for correct sharpening instructi

English – 11ASSEMBLYFitting the loop handle(GT 2125)• Position the handle on the shaft. Note that the handle must be mounted below the arrow on the sh

12 – EnglishASSEMBLYDismantling:• Undo the knob (at least three turns).• Push the knob towards the coupling.• Carefully twist the lower half of the sh

English – 13ASSEMBLYFitting the blade guard/combination guard, grass blade and grass cutter(GC 2125, GC 2125C)• Hook the blade guard/combination guard

14 – EnglishFUEL HANDLINGFuel safetyNever start the machine:1 If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporat

English – 15FUEL HANDLINGMixing• Always mix the gasoline and oil in a clean container intended for fuel.• Always start by filling half the amount of th

16 – EnglishSTARTING AND STOPPINGCheck before starting• Never start the machine indoors. Exhaust fumes can be dangerous if inhaled.• Observe your surr

English – 17STARTING AND STOPPINGStartingPrimer bulb: Press the primer bulb repeatedly until fuel begins to fill the bulb. The bulb need not be complet

18 – EnglishWORKING TECHNIQUESGeneral working instructionsBasic safety rules1 Look around you:• To ensure that people, animals or other things cannot

English – 19WORKING TECHNIQUES• Work systematically to and fro across the area, clearing a width of around 4-5 m on each pass. This exploits the full

2 – English KEY T O SYMBOLS Symbols WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in s

20 – EnglishWORKING TECHNIQUESCutting• The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep the cord paral

English – 21MAINTENANCECarburetorYour Jonsered product has been designed and manufactured to specifications that reduce harmful exhaust fumes. The engi

22 – EnglishMAINTENANCEFine adjustment of the idle speed TAdjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. Fir

English – 23MAINTENANCECooling systemTo keep the working temperature as low as possible the machine is equipped with a cooling system.The cooling syst

24 – EnglishMAINTENANCETwo-piece shaft (GC 2125C)The drive shaft end in the lower shaft should be lubricated with grease every 30 hours. There is a ri

English – 25MAINTENANCEMaintenance scheduleThe following is a list of the maintenance that must be performed on the machine. Most of the items are des

26 – EnglishTECHNICAL DATATechnical dataNote 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure lev

English – 27TECHNICAL DATAApproved accessories Type Cutting attachment guard, Art. no.GT 2125Blade shaft thread 3/8 RTrimmer head Tap-N-Go VII (R) 530

28 – EnglishFEDERAL EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONSThe EPA (The US Environmental Protection Agency), Environme

"Clic"12356796,0 m18'483,05 m9'2,0-2,4 mm.079-.095"10 cm 4"6"15 cmTap-N-Go 25

English – 3 CONTENTS Contents Note the f ollowing before starting: Please read the oper ator’s manual carefully.Long-term exposure to noise can res

1Trimmy H II234567897,5 m 25'2,0-2,4 mm.080-.095"12 15 cm 6"~ 3,7 m 12' 15 cm 6"

"Clic"12356710118,5 m28'484,2 m14'2,4-2,7 mm.095-.106"10 cm 4"6"15 cmS35

12432,4-2,7 mm.095-.106"4,25 m14'4,25 m14'B6"15 cmA6"15 cmS355

Tap-N-Go 35"Clic"12356798,5 m28'484,3 m14'2,4-2,7 mm.095-.106"10 cm 4"6"15 cm

´®z*x°G¶5p¨´®z*x°G¶5p¨1Auto 3223456789104,0 m 13'2,4 mm.095"~2,0 m6,5'6"6"15 cm15 cm

´®z*x°G¶5p¨2005-03-15´®z*x°G¶5p¨1088953-95

4 – English INTR ODUCTION Dear customer! Cong ratulations on your choice to buy a Jonsered product!Your purchase gives you access to professional h

English – 5 WHA T IS WHA T? What is what?3130GC2125C 1 Trimmer head2 Grease filler cap, bevel gear3 Bevel gear4 Cutting attachment guard5 Shaft6 Lo

6 – English GENERAL SAFETY PRECA UTIONS Impor tantPersonal protective equipment HEARING PR OTECTIONWear hearing protection that provides adequate n

English – 7 GENERAL SAFETY PRECA UTIONS Mac hine ′′′′ s safety equipment This section descr ibes the machine ′ s safety equipment, its purpose, an

8 – English GENERAL SAFETY PRECA UTIONS Vibration damping system Y our machine is equipped with a vibration damping system that is designed to redu

English – 9GENERAL SAFETY PRECAUTIONSLocking nutA locking nut is used to secure some types of cutting attachment.When fitting, tighten the nut in the o