Jonsered GT2125L Bedienungsanleitung

Operator´s manual (EPA)Please read these instructions carefullyand make sure you understand thembefore using the machine.

10 – EnglishSAFETY INSTRUCTIONSClearing• The clearing techniqueremoves all unwantedvegetation. Keep thetrimmer head just abovethe ground and tilt it.L

English – 11WHAT IS WHAT?What is what on the trimmer?1. Trimmer head2. Grease filler cap3. Angle gear4. Spray guard5. Shaft6. Loop handlebar7. Throttl

12 – EnglishASSEMBLYAssembling the loop handlebar(GT2125L)Assembly of the trimmer headIt is extremely importantthat the disc drive’s/supportflange’s g

English – 13ASSEMBLY• Fit the guard (A)intended for use withthe trimmer head. Hookthe guard onto the shaftfitting and secure it withthe bolt (L).• Fit

14 – EnglishFUEL HANDLINGFuel mixtureNOTE!The machine is fitted with a two-stroke engine and mustalways be run on a mixture of petrol and two-stroke o

English – 15START AND STOPControl before startingFor reasons of safety followthese recommendations!• Check that the supportflange is not cracked due t

16 – EnglishBasic setting• The carburettor is set to its basic setting when test run at thefactory. The basic setting is richer than the optimal setti

English – 17MAINTENANCEHneedle. The high speed needle is adjusted correctly when themachine ‘splatters’ a little . If the machine smokes heavily atthe

18 – FrançaiseENTRETIENCircuit de refroidissementPour obtenir unetempérature de service aussibasse que possible, le moteurest muni d’un circuit derefr

English – 19MAINTENANCEThe angle gear is filled with asufficient quantity of grease atthe factory. However, beforeusing the machine you shouldcheck th

2 – EnglishSymbolsSYMBOL EXPLANATIONWARNING! Clearing saws,brushcutters and trimmers can bedangerous!Careless or incorrect use can result inserious or

20 – EnglishTECHNICAL DATATechnical dataEngineDisplacement, cu. in/cm3Cylinder bore, inch/mmStroke length, inch/mmRecommended max. speed, rpmIdling sp

English – 21EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS ANDOBLIGATIONSThe EPA (U.S. Environmental Protection Agency),Environment Canada an

22 – English1Poly Trim2345678>20mm>20mm!BA6 NmX 10

English – 231Trimmy H II234567897,5 m 25'2,0-2,4 mm.080-.095"12 15 cm 6"~ 3,7 m 12' 15 cm 6"

24 – English1Trimmy Hit Pro2567891012“Click”347,5 m 25'2,0-2,4 mm.080-.095"15 cm 6"~ 3,7 m 12'1.)2.)1115 cm 6"15

English – 256"2)1)~ 15 cm 6"789101115 cm1234567,0 m 23"2,0- mm,080-."12 cm 5"~ 3,5 m 11"Trimmy VII

26 – English1Tap-N-Go Pro2567891012“Click”347,5 m 25'2,0-2,4 mm.080-.095"15 cm 6"~ 3,7 m 12'1.)2.)1115 cm 6"15 c

2002W11´*xty¶5s¨108 88 48-95

English – 3CONTENTSList of contentsSYMBOL EXPLANATIONSymbols ... 2CONTENTS

4 – EnglishThe machine‘s safety equipmentThis section describes the machine‘s safety equipment, itsfunction and how checks and maintenance are carried

English – 5SAFETY INSTRUCTIONS4. Vibrationdamping systemYour machine is equippedwith a vibration dampingsystem, which is designedto give as vibration-

6 – English3. Cuttingattachment guard• Ensure that the sprayguard is undamaged andis not cracked.• Replace the guard if ithas been exposed toimpact or

English – 7SAFETY INSTRUCTIONS6. Cutting equipmentThe section describes how through correct maintenance andthrough using the right type of cutting equ

8 – EnglishSAFETY INSTRUCTIONSGeneral safety instructionsTransport and storage• Store and transport the machine and fuel so that any leakageor fumes d

English – 9!General working instructionsSAFETY INSTRUCTIONSBasic working techniques• Always drop to idling speed after each working operation.Longer p